Shaped windows are any windows that are not a plain rectangle: arched heads, full circles and ovals, gable apex frames that follow a roof pitch, triangles, trapezoids and one-off bespoke outlines. They are made to measure from an accurate survey or a template of the opening, and most are fixed, with any opening sections placed in the rectangular part below. We fabricate aluminium windows at our own Fifield workshop and supply UPVC windows, so we can advise on which shapes suit which material. Ask us and we’ll confirm what is possible for your shape and sizes. For our wider ranges, see aluminium windows and doors and UPVC windows and doors.

Common shapes
Arched windows
Arches come in several forms. A segmental arch is a shallow curve, common over Victorian and Edwardian windows in brick. A semicircular or full-radius arch forms half a circle, seen on Georgian-style fanlights and stair windows. A gothic or pointed arch meets at a peak, found on chapels, lodges and some Victorian villas. Getting the arch right means matching the curve to the brickwork, not just the width and height.
Circular and oval windows
Round “porthole” or bullseye windows appear on gables, landings and bathrooms. They are usually fixed, though some can include a small opening section depending on the system and size.
Gable apex and raking windows
Gable windows follow the slope of a roof, often above sliding or bifold doors in an extension or a garden room. They can be a single triangle, a trapezoid with a flat top, or a run of frames stepping up the pitch. They are a good way to bring light into a vaulted ceiling. See our sliding doors and bifold doors pages for the doors below.
Bespoke outlines
Hexagons, quarter circles, eyebrow windows and irregular shapes in barn conversions or architect-designed homes can often be made, subject to the limits of the frame system.
“Professional service, good communication and attention to detail throughout the job. The finished work looks fantastic and was exactly what I needed.”
“Everything from the sales to the installation was a perfect experience. We love our sliding doors and windows.”
“Excellent work done in installing the new door. Price was very competitive. Would highly recommend.”
How shaped windows are made
- Survey or template. For simple shapes we take precise measurements of width, height and rise. For complex curves or old brick arches we make a template of the opening, because old arches are rarely a perfect geometric curve.
- Frame fabrication. Profiles are bent to the required radius for curves, or cut and jointed at the right angles for straight-sided shapes.
- Glass. Sealed units are made to the exact shape, so lead times can be longer than for standard rectangles.
- Fitting. The frame is fixed and sealed into the opening, with particular care at the head where curves meet brickwork.
Design choices
- Fixed or opening. Most shaped sections are fixed. Where you need ventilation, an opening casement in the rectangular part below an arch is the usual answer.
- One frame or two. An arched window can be one frame with a curved head, or a rectangular window with a separate arched fanlight above. One frame looks cleaner; two frames can be easier to fabricate and replace.
- Glazing bars. Radiating bars in a fanlight, or bars following the curve, add a period touch. See Georgian windows.
- Glass. Shaped windows on landings and bathrooms often use obscure glass or decorative glass.
- Colour. Match the shaped frames to the rest of the house; see window colours.
Practical limits
- Tight radii. Every profile has a minimum bending radius. Very small circles or tight curves may not be possible in a given system.
- Sharp angles. Very acute triangles leave a narrow point where the frame takes up most of the glass area.
- Size and weight. Large gable glazing needs structural support and may need mullions or transoms to break it up.
- Blinds. Few blinds fit shaped glass. Ask about options at the design stage; see blinds.
- Cost. Bending, templating and shaped glass all add cost compared with a rectangle of the same area.
Regulations to consider
Large shaped windows above doors or near the floor may fall within the critical locations for safety glazing in Approved Document K. Councils such as Richmond summarise these as glass within 800mm of the floor, glass in doors up to 1500mm, and glass within 300mm of a door up to 1500mm. Gable glazing beside or close above doors can extend into these zones and should then be toughened or laminated.
If a shaped window is the main window in a first-floor bedroom, it must still provide an escape opening; Richmond’s guidance gives the usual minimum as 0.33m², at least 450mm wide and high, with a cill no higher than 1100mm. A round or arched window may not achieve this on its own.
New shaped openings in existing walls, or big gable glazing in an extension, may need planning permission or Building Regulations approval, and the Planning Portal notes that upper-floor side windows have extra conditions. Check with your council.
Common mistakes
- Measuring only width and height on an old arch, so the curve does not match the brickwork.
- Expecting a small round window to open fully.
- Leaving safety glass out of low-level gable glazing beside doors.
- Planning blinds after the windows are ordered.
Care
Clean shaped frames as you would any window, with mild soapy water. Check the sealant at the head of arches every year or two, as this is where water tends to find its way in.

Talk to us about your shape
We fabricate aluminium windows from £750 + VAT at our Fifield workshop near Windsor and supply UPVC on the Selecta Advance 70 system, with lead times from 10 days on standard windows and a 10-year guarantee. We cover Berkshire, Buckinghamshire, Surrey, west Kent and north West Sussex. Call 01753 965 005 or request a quote and we will survey or template your opening.
Frequently asked questions
Can arched windows open?
The arched head itself is normally fixed, because hinging a curved sash is difficult and costly. The usual arrangement is a fixed arched top with opening casements in the rectangular section below, which gives ventilation and looks seamless. Whether any curved section can open depends on the system and size, so ask us to confirm.
How do you measure for a shaped window?
For simple shapes we measure width, height and the rise of the curve or the roof pitch. For old brick arches and complex outlines we make a physical template of the opening, because old arches are rarely a perfect curve. The frame and glass are then made to that template so they fit closely.
Are shaped windows more expensive than standard windows?
Yes, usually. Bending profiles, making templates and producing shaped glass units take more time and material than a rectangle of the same area. Simple angled shapes such as gable triangles generally cost less than tight curves. We price each shape individually after the survey so you know the cost before ordering.
Do gable windows above doors need safety glass?
Sometimes. Glass in doors up to 1500mm, within 300mm of a door up to 1500mm, or within 800mm of the floor elsewhere is in a critical location under Approved Document K and must be toughened or laminated. Gable glazing that comes down beside or close to doors can fall in these zones, so we check each design.
Can you make round or circular windows?
Round windows can be made, subject to the minimum bending radius of the frame profile. Most are fixed, with any ventilation provided elsewhere in the room. Very small diameters may not be possible in every system. Ask us and we will confirm what can be made for your system and size after we survey.